The terminal clamps are used to hold the aluminum straps in compression around the circumference of the Starbars. The aluminum strap and terminal clamp should be installed at the very end of the Starbar.

The "T" type is used with an expansion tool, and is useful for installations where space is limited.

Category:

Sizing Breakdown

Item #Item NameStarbar DiameterInside DiameterWidthDistance Between Wings
T-10T - Type Terminal Clamp0.38 Inch
10 mm
400 Amp0.50 Inch
13 mm
N/A
T-11/13T - Type Terminal Clamp0.44 Inch
11 mm
400 Amp0.50 Inch
13 mm
N/A
T-11/13T - Type Terminal Clamp0.50 Inch
13 mm
400 Amp0.50 Inch
13 mm
N/A
T-16T - Type Terminal Clamp0.63 Inch
16 mm
400 Amp0.50 Inch
13 mm
N/A
T-19T - Type Terminal Clamp0.75 Inch
19 mm
400 Amp 0.75 Inch
19 mm
N/A
T-25T - Type Terminal Clamp1.00 Inch
25 mm
400 Amp 1.00 Inch
25 mm
N/A
T-32T - Type Terminal Clamp1.25 Inch
32 mm
400 Amp1.25 Inch
32 mm
N/A
T-35/38T - Type Terminal Clamp1.38 Inch
35 mm
400 Amp1.25 Inch
32 mm
N/A
T-54T - Type Terminal Clamp2.12 Inch
54 mm
400 Amp1.50 Inch
38 mm
N/A
T-70T - Type Terminal Clamp2.75 Inch
70 mm
400 Amp1.50 Inch
38 mm
N/A
T-90Expansion ToolN/AN/AN/AN/A
T-100Expansion ToolN/AN/AN/AN/A
T-110Expansion ToolN/AN/AN/AN/A
T-35/38T - Type Terminal Clamp1.50 Inch
38 mm
400 Amp1.25 Inch
32 mm
N/A
T-44T - Type Terminal Clamp1.75 Inch
44 mm
400 Amp1.50 Inch
38 mm
N/A

Terminal Clamps Chart

Starbar Diameter T – Type Terminal Clamps *Tool
(T) Part Number Inside Diameter Width
MM Inch P/N MM Inch MM Inch P/N
7 0.25 N/A          
10 0.38 T-10 11 0.40 13 0.50 T-90
11 0.44 T-11/13 13 0.50 13 0.50 T-90
13 0.50 T-11/13 13 0.50 13 0.50 T-90
16 0.63 T-16 16 0.65 13 0.50 T-90
19 0.75 T-19 19 0.75 19 0.75 T-90
25 1.00 T-25 25 1.00 25 1.00 T-90
32 1.25 T-32 30 1.20 32 1.25 T-100
35 1.38 T-35/38 35 1.40 32 1.25 T-100
38 1.50 T-35/38 35 1.40 32 1.25 T-100
44 1.75 T-44 40 1.60 38 1.50 T-100
54 2.12 T-54 51 2.00 38 1.50 T-100
70 2.75 T-70 63 2.50 38 1.50 T-110
The T-100+5 is an extended tool that can be used as a substitute for the T-100. An extended tool is not available for the T-90.
*The T-RA (right angle tool) can be used on any of the T-type clamps.

Specifications

Temperature Limitation

Clamps are made from heat resistant steel and should never be operated in an ambient temperature over 500ºF (260ºC).

Identification

The stainless steel clamps are stamped with a number for easy identification and proper matching to the correct diameter Starbars. The expansion tools have the part numbers marked on the handle.

Availability

Most sizes are available from stock. Others can be shipped in one week, or quicker for emergencies.

Expansion Tool

T-90

Notes

The T-100+5 is an extended tool that can be used as a substitute for the T-100. An extended tool is not available for the T-90.

  REQUEST INFORMATION