The strap assembly is offered in 75, 150, 200, 400 and 600 amperage rating. The binding post to Moly-D (K type strap) is offered for the 4/9, 6/12, 9/18 and 12/24 elements. There are two styles available for the 3/6 element; E-type for connecting binding post to Moly-D, and F-type for connecting Moly-D to Moly-D.

Category:

Specifications

Element sizes

4/9
12/24
3/6
6/12
9/18

Identification

Combination straps are described by the element size and working length in centimeters. As an example, the part number for a 75 ampere 3/6 E-2 type strap with a 10 centimeter working length would be an E210.

Availability

E, F, & K straps are available from stock in standard and custom lengths and can be shipped 2-3 days after receipt of an order.

Installation instructions

The combination clamp and strap of the recommended size should always be used. The element terminal ends get hot from the I2R energy in the cold ends and from the heat conducted from the hot zone out along the cold ends. Using electrical straps of a smaller size or different material can cause the element cold ends and straps to overheat and fail.

Although we offer the F type strap that is used to connect two elements together, we don’t recommend their use.

We recommend the E or K type strap be used to connect the element to a post or another E or K type strap.

It is very important that Moly-D straps be initially tightened securely. After the elements are brought to temperature, the nut and bolt should be tightened again. Allow about 24 hours between tightening for the clamp portion of the straps relaxes on the first heating and becomes loose on the element.

If the clamp is loose, it causes a poor electrical connection that is high in resistance which causes the element terminal end to overheat. This can cause the element and terminal strap to fail.

The strap must not cause a bending force, i.e. side force on the element. This will cause the heating section (Le) to bend and possibly break. We recommend the working length of the strap be approximately 12 mm longer than the distance between the two connecting points.

Failure to properly maintain strap-to-element connection will lead to premature failure of element and strap.

If previously used straps are used with new elements they should be examined. Any straps with white powder, broken wire strands, or small globules of aluminum should not be used.

When installing Moly-D elements or straps for the first time:

1. Tighten all strap-to-element connections as follows.

Table C- Torque Range
Strap Size Cold End (Lu)
Diameter
Torque Range
Inch lbs Kg meter
Min. Max. Min. Max.
E2 or F2 6 mm 24 108 0.277 1.24
K3 or K3 9 mm 24 108 0.277 1.24
K4 or K4 12 mm 48 108 0.553 1.24
K5 or K5 18 mm 48 108 0.553 1.24
* If a torque wrench is not available, connections should be tight enough such that the strap will not move independent of the element.

2. Always tighten with two wrenches. Avoid twisting the element.
3. Always use the torque wrench on the nut.
4. Tighten toward the higher end of the torque range if possible.

For cyclic operation of furnace and elements – Follow the instructions below:

After first heating cycle:

  1. Allow elements and straps to cool to near room temperature.
  2. Re-tighten all strap-to-element connections using same instructions as shown in table C.
  3. Connections should now remain tight for awhile, however, routinely check strap-to-element connections and adjust as needed.

For continuous operation of furnace and elements after installation – Follow the instructions below:
Approximately 48 hours after Moly-D elements have achieved temperature for the first time, or at an appropriate time within the cycle:

  1. Turn off power to furnace and elements.
  2. Re-tighten all strap-to-element connections using same instructions as above.

Use caution when working with hot elements and straps. Use only approved I Squared R Element straps and accessories.

  REQUEST INFORMATION